A Systematic Literature Review of Total Productive Maintenance on Industries

Setiawan San

Abstract

Attempts to achieve optimization of machine and equipment maintenance at manufacturing companies over the years have encountered a multitude of problems. Due to equipment losses such as setup and adjustment, minor stops and delays, defective products due to equipment, reduced engine speed, and reduced output has influenced their desire to reach world class manufacturing levels. This paper discusses a large part of the TPM approach in manufacturing companies and provides an overview of the various TPM implementation practices demonstrated by manufacturing companies in the world.. Based on review results of the 50 journals about TPM in industries It was found that most of the TPM implementations used the OEE parameter to see the success rate of implementing this TPM. This paper also highlights the variable approach that is most widely used by various practitioners and researchers and evaluates in detail the success factors of implementing TPM and the reasons behind the failure of implementing TPM are also discussed so as to ensure the implementation of TPM can run smoothly and effectively in manufacturing companies

Keywords

Total Productive Maintenance (TPM), Overall Equipment Effectiveness (OEE), 8 pillar

Full Text:

PDF

References

Adesta, E. Y.T., Prabowo, H. A., & Agusman, D. (2018). Evaluating 8 pillars of Total Productive Maintenance (TPM) implementation and their contribution to manufacturing performance. IOP Conference Series: Materials Science and Engineering, 290(1). https://doi.org/10.1088/1757-899X/290/1/012024

Adesta, Erry Yulian Triblas, & Prabowo, H. A. (2018). Total Productive Maintenance (TPM) implementation based on lean manufacturing tools in Indonesian manufacturing industries. International Journal of Engineering and Technology(UAE), 7(3.7 Special Issue 7), 156–159. https://doi.org/10.14419/ijet.v7i3.7.16261

Ahuja, I. P. S., & Khamba, J. S. (2008). Total productive maintenance: Literature review and directions. International Journal of Quality and Reliability Management, 25(7), 709–756. https://doi.org/10.1108/02656710810890890

Ali, A. Y. (2019). Application of Total Productive Maintenance in Service Organization. 8(2), 176–186. https://doi.org/10.22105/riej.2019.170507.1076 Almeanazel, O. T. R. (2010). Total Productive Maintenance Review and Overall Equipment. Jordan Journal of MMechanical and Industrial Engineering, 4(4), 517–522.

Amrussalam, A., Budi Santoso, P., & Pambudi Tama, I. (2016). Pengukuran Dan Perbaikan Total Productive Maintenance (Tpm) Menggunakan Overall Equipment Effectiveness (Oee) Dan Root Cause Failure Analysis (Rcfa). Journal of Engineering and Management Industial System, 4(2), 102–108. https://doi.org/10.21776/ub.jemis.2016.004.02.1

Anh, P. C. (2012). Contribution of Total Productive Maintenance To Quality Performance. The Journal of Japanese Operations Management and Strategy, 3(1), 38–54. https://doi.org/10.20586/joms.3.1_38

Anthony, M. B. (2019). Analisis Penerapan Total Productive Maintenance (TPM) Menggunakan Overall Equipment Efectiveness (OEE) Dan Six Big Losses Pada Mesin Cold Leveller PT. KPS. JATI UNIK : Jurnal Ilmiah Teknik Dan Manajemen Industri, 2(1), 29. https://doi.org/10.30737/jatiunik.v2i2.333

Arya Wiguna. (2015). IMPLEMENTASI PROGRAM TPM (TOTAL PRODUCTIVE MAINTENANCE) MESIN CJ4 DI PT. KIMBERLY-CLARK INDONESIA IGR. OE, 49(23–6), 23–34. http://www.ti.com/lit/ds/symlink/cc2538.html

Azid, N. A. A., Shamsudin, S. N. A., Yusoff, M. S., & Samat, H. A. (2019). Conceptual Analysis and Survey of Total Productive Maintenance (TPM) and Reliability Centered Maintenance (RCM) Relationship. IOP Conference Series: Materials Science and Engineering, 530(1). https://doi.org/10.1088/1757-899X/530/1/012050

Brah, S. A., & Chong, W. K. (2004). Relationship between total productive maintenance and performance. International Journal of Production Research, 42(12), 2383–2401. https://doi.org/10.1080/00207540410001661418

Brodny, J., & Tutak, M. (2017). Application of Elements of TPM Strategy for Operation Analysis of Mining Machine. IOP Conference Series: Earth and Environmental Science, 95(4). https://doi.org/10.1088/1755-1315/95/4/042019

Chan, F. T. S., Lau, H. C. W., Ip, R. W. L., Chan, H. K., & Kong, S. (2005). Implementation of total productive maintenance: A case study. International Journal of Production Economics, 95(1), 71–94. https://doi.org/10.1016/j.ijpe.2003.10.021

Didikwahjudi, & Soejonotjitro, R. (2009). Studi Kasus Peningkatan Overall Equipment Effectiveness ( OEE ) Melalui Implementasi Total Productive Maintenance ( TPM ). Seminar Nasional Teknik Mesin IV, 30(June 2009).

Dyah Ika Rinawati, N. C. D. (2014). Analisis Penerapan Total Productive Maintenance (TPM) Menggunakan Overall Equipment Effectiveness (OEE) dan Six Big Losses pada Mesin Cavitec di PT. Essentra Surabaya. Prosiding Seminar Nasional Teknologi Dan Informatika, Volume 11(1), 21–26. https://doi.org/10.32734/ee.v1i2.245

Fahmi, A., Rahman, A., & Efranto, R. (2013). Implementasi Total Productive Maintenance Sebagai Penunjang Produktivitas Dengan Pengukuran Overall Equipment Effectiveness Pada Mesin Rotary KTH-8 (Studi Kasus PT.Indonesian Tobacco). Jurnal Rekayasa Dan Manajemen Sistem Industri, 1(1), 75–84. http://jrmsi.studentjournal.ub.ac.id/index.php/jrmsi/article/view/15/37

Fam, S. F., Prastyo, D. D., Loh, S. L., Utami, S., & Yong, D. H. Y. (2018). Total productive maintenance practices in manufacture of electronic components & boards industry in Malaysia. Journal of Telecommunication, Electronic and Computer Engineering, 10(2–8), 97–101.

Gallesi-Torres, A., Velarde-Cabrera, A., León-Chavarri, C., Raymundo-Ibañez, C., & Dominguez, F. (2020). Maintenance Management Model under the TPM approach to Reduce Machine Breakdowns in Peruvian Giant Squid Processing SMEs. IOP Conference Series: Materials Science and Engineering, 796(1). https://doi.org/10.1088/1757-899X/796/1/012006

Habidin, N. F., Hudin, N. S., Mustaffa, W. S. binti W., Rosli, S. A. M., Ong, S. Y. Y., Fuzi, N. M., & Zulkifle, N. N. (2017). A Proposed Total Productive Maintenance (TPM) Tool for Lean Dashboard, Statistics and Performance Efficiency in Malaysian Modern Manufacturer. International Journal of Academic Research in Business and Social Sciences, 7(6), 1012–1018. https://doi.org/10.6007/ijarbss/v7-i6/3061

Hairiyah, N., Rizki, R., & Wijaya, R. A. (2019). Analisis Total Productive Maintenance (Tpm) Pada Stasiun Kernel Crushing Plant (Kcp) Di Pt. X. Jurnal Teknologi Pertanian Andalas, 23(1), 103. https://doi.org/10.25077/jtpa.23.1.103-110.2019

Haryono, L., & Susanty, A. (2015). Penerapan Total Productive Maintenance Dengan Pendekatan Overall Equipment Effectiveness (OEE) Dan Penentuan Kebijakan Maintenance Pada Mesin Ring Frame Divisi Spinning I Di Pt Pisma Putra Textile. J@ti Undip: Jurnal Teknik Industri, 4(4).

Herry, A. P., Farida, F., & Lutfia, N. I. (2018). Performance analysis of TPM implementation through Overall Equipment Effectiveness (OEE) and Six Big Losses. IOP Conference Series: Materials Science and Engineering, 453(1). https://doi.org/10.1088/1757-899X/453/1/012061 Ireland, F., & Dale, B. G. (2001). A study of total productive maintenance implementation. Journal of Quality in Maintenance Engineering, 7(3), 183–191. https://doi.org/10.1108/13552510110404495

Irwansyah, D., Harahap, M. R. F., Erliana, C. I., Abdullah, D., Sari, A., Siregar, N., Achmaddaengs, G. S., Indahingwati, A., Sumartono, E., Wilujeng, S., Nurmawati, Subekti, P., Kurniasih, N., Rosalina, F., & Hartono, H. (2019). Improvement Suggestion Performance of Blowing Machine Line 4 with Total Productive Maintenance (TPM) Method at PT. Coca-Cola Amatil Indonesia MedanUnit. Journal of Physics: Conference Series, 1361(1). https://doi.org/10.1088/1742-6596/1361/1/012053

Jain, A., Bhatti, R., & Singh, H. (2014). Total productive maintenance (TPM) implementation practice: a literature review and directions. In International Journal of Lean Six Sigma (Vol. 5, Issue 3). https://doi.org/10.1108/IJLSS-06-2013-0032

Krisnaningsih, E. (2015). Usulan Penerapan TPM dalam Rangka Peningkatan Efektifitas Mesin dengan OEE sebagai Alat Ukur di PT XYZ. Usulan Penerapan Tpm Dalam Rangka Peningkatan Efektifitas Mesin Dengan Oee Sebagai Alat Ukur Di Pt Xyz, 2(2), 13–26.

Lazim, H. M., Salleh, M. N., Subramaniam, C., & Othman, S. N. (2013). Total Productive Maintenance and Manufacturing Performance: Doeas Technical Complexity in the Production Process Matter? International Journal of Trade, Economics and Finance, 4(6), 380–383. https://doi.org/10.7763/ijtef.2013.v4.321

Liu, X., & Rubert, P. (2005). Mapping surface properties of sinusoidal roughness standards by TPM. Journal of Physics: Conference Series, 13(1), 20–23. https://doi.org/10.1088/1742-6596/13/1/005

Lukmandono, Prabowo, R., & Sulistyowati, E. (2020). Analysis of Total Productive Maintenance (TPM) and Failure Mode And Effect Analysis (FMEA) to improve machine effectiveness: A study on Indonesia’s sugar mills. IOP Conference Series: Materials Science and Engineering, 885, 012063. https://doi.org/10.1088/1757-899x/885/1/012063

Manik, R. F. (2018). Analisis Produktivitas Dengan Metode Overall Equipment Effectiveness (Oee) Dalam Penerapan Total Productive Maintenance ( Tpm ) Pada Mesin Polymer. 1(004201305051), 53–64.

Martomo, Z. I., & Laksono, P. W. (2018). Analysis of total productive maintenance (TPM) implementation using overall equipment effectiveness (OEE) and six big losses: A case study. AIP Conference Proceedings, 1931. https://doi.org/10.1063/1.5024085

Martono, N. (2014). Metode penelitian kuantitatif: Analisis Isi dan Analisis Data Sekunder (Ed Revisi). Raja Grafindo Persada. McKone, K. E., Schroeder, R. G., & Cua, K. O. (1999). Total productive maintenance: A contextual view. Journal of Operations Management, 17(2), 123–144. https://doi.org/10.1016/S0272-6963(98)00039-4

Meca Vital, J. C., & Camello Lima, C. R. (2020). Total Productive Maintenance and the Impact of Each Implemented Pillar in the Overall Equipment Effectiveness. International Journal of Engineering and Management Research, 10(02), 142–150. https://doi.org/10.31033/ijemr.10.2.17

Muchiri, P., & Pintelon, L. (2008). Performance measurement using overall equipment effectiveness (OEE): Literature review and practical application discussion. International Journal of Production Research, 46(13), 3517–3535. https://doi.org/10.1080/00207540601142645

Nasurdin, A. M., Jantan, M., Peng, W. W., & Ramayah, T. (2005). Influence of Employee Involvement in Total Productive Maintenance Practices on Job Characteristics: The Malaysian Scenario. Gadjah Mada International Journal of Business, 7(3), 287. https://doi.org/10.22146/gamaijb.5580

Nishal, M., Ramprasad, K., Theja, A. J. A., Saravanan, S. A., & Abishek, S. (2018). Need for Total Productive Maintenance in Sme and. 6, 15–20.

Nurfaizah, U., Adianto, R. H., & Prassetiyo, H. (2014). Rancangan Penerapan Total Productive Maintenance (TPM) Di Bagian Press II PT. XYZ. Reka Integra, 2(1), 340–353.

Nurprihatin, F., Angely, M., & Tannady, H. (2019). Total productive maintenance policy to increase effectiveness and maintenance performance using overall equipment effectiveness. Journal of Applied Research on Industrial Engineering, 6(3), 184–199. https://doi.org/10.22105/jarie.2019.199037.1104

Nursubiyantoro, E., Puryani, P., & Rozaq, M. I. (2016). Implementasi Total Productive Maintenance (Tpm) Dalam Penerapan Overall Equipment Effectiveness (Oee). Opsi, 9(01), 24. https://doi.org/10.31315/opsi.v9i01.2169

Okpala, C. C., Anozie, S. C., & Ezeanyim, O. C. (2018). The Application of Tools and Techniques of Total Productive Maintenance in Manufacturing. International Journal of Semantic Computing, 8(6), 18115–18121.

One Yoon Seng, Muhamad Jantan, T. R. (2004). Implementing Total Productive Maintenance (TPM) In Malaysian Manufacturing Organisation: An Operational Strategy Study. Kinerja, 9(1), 163–173.

Palomino-Valles, A., Tokumori-Wong, M., Castro-Rangel, P., Raymundo-Ibañez, C., & Dominguez, F. (2020). TPM Maintenance Management Model Focused on Reliability that Enables the Increase of the Availability of Heavy Equipment in the Construction Sector. IOP Conference Series: Materials Science and Engineering, 796(1). https://doi.org/10.1088/1757-899X/796/1/012008

Parikh, Y., & Mahamuni, P. (2015). Total Productive Maintenance : Need & Framework. International Journal of Innovative Research in Advance Engineering, 2(2), 126–130.

Prashanth Pai, M., Ramachandra, C. G., Srinivas, T. R., & Raghavendra, M. J. (2018). A Study on Usage of Total Productive Maintenance (TPM) in Selected SMEs. IOP Conference Series: Materials Science and Engineering, 376(1). https://doi.org/10.1088/1757-899X/376/1/012117

Priyono, S., Machfud, M., & Maulana, A. (2019). Penerapan Total Productive Maintenance (TPM) Pada Pabrik Gula Rafinasi di Indonesia (Studi Kasus: PT. XYZ). Jurnal Aplikasi Bisnis Dan Manajemen, 5(2), 265–277. https://doi.org/10.17358/jabm.5.2.265

Reyes, J., Alvarez, K., Martínez, A., & Guamán, J. (2018). Total productive maintenance for the sewing process in footwear. Journal of Industrial Engineering and Management, 11(4), 814–822. https://doi.org/10.3926/jiem.2644

Sariyusda, S., Fakhriza, F., & Putra, J. (2016). Analisa Efektivitas Prokdusi Pada Unit Urea I Dengan Menggunakan Metode Total Productive Maintenance (Tpm) Di Pt. Pupuk Iskandar Muda. Jurnal POLIMESIN, 14(1), 37. https://doi.org/10.30811/jpl.v14i1.300

Sethia, C. S., Shende, N., & Dange, S. S. (2016). A Case Study on Total Productive Maintenance in Rolling Mill. International Journal of Scientific Development and Research, 1(5), 283–289. www.ijsdr.org

Singh, R., Gohil, A. M., Shah, D. B., & Desai, S. (2013). Total productive maintenance (TPM) implementation in a machine shop: A case study. Procedia Engineering, 51(NUiCONE 2012), 592–599. https://doi.org/10.1016/j.proeng.2013.01.084

Sutoni, A., Setyawan, W., & Munandar, T. (2019). Total Productive Maintenance (TPM) Analysis on Lathe Machines using the Overall Equipment Effectiveness Method and Six Big Losses. Journal of Physics: Conference Series, 1179(1). https://doi.org/10.1088/1742-6596/1179/1/012089

Tondato, R., & Gonçalves, M. B. (2013). Total Productive Maintenance: A casey study. 22nd International Conference on Production Research, ICPR 2013, 12(1).

Venkateswaran, N. (2017). Arabian Journal of Business and Total Productive Maintenance ( TPM ) Practices Adopted at Manufacturing Unit : An Analysis. Arabian Journal of Business and Management Review, 7(4). https://doi.org/10.4172/2223-5833.1000313

Vigneshwaranp, S., Maranp, M., & Manikandanp, G. (2015). Impact of TPM Implementation: Literature Review and Direction. IJISET-International Journal of Innovative Science, Engineering & Technology, 2(12), 12. www.ijiset.com

Wang, F. K. (2006). Evaluating the efficiency of implementing total productive maintenance. Total Quality Management and Business Excellence, 17(5), 655 –667. https://doi.org/10.1080/14783360600588232

DOI: https://doi.org/10.20961/performa.20.2.50087

Refbacks

  • There are currently no refbacks.