Studi eksperimental pengaturan waktu pengapian pada mesin 4 langkah 1 silinder berbahan bakar E25

Arjuna AJi, Budi Santoso, Dominicus Danardono

Abstract

The use of ethanol as a mixture of premium is for reducing dependency to the primuim, considering that premium is not renewable. The goal of the ethanol addition in a fuel is to increase the octane number. However the heating value of the ethanol is lower then premium, so it will decrease the performance of the SI engine. The study aimed for increasing the performance of SI engine using E25 as mixture of premium-ethanol. The performance of engine was measured by engine test bed on chassis. Change load method is used in the experiment. The experiments result is advancing the time of ignition at 4 degree that can improve the engine performance. The result of changes load use E25 fuel with advanced time of ignition at 4 degree can increase engine performance as torque, power, bmep, efficiency thermal and bsfc were decrease.

Full Text:

PDF

References

F. A. Agrariksa, B. Susilo, dan W. A. Nugroho, “Uji Peformasi Motor Bakar Bensin (On Chasis) Menggunakan Campuran Premium dan Etanol,” Jurnal Keteknikan Pertanian Tropis dan Biosistem, vol. 1, no. 3, pp. 194-203, 2013.

J. B. Heywood, “Internal Combustion Engine Fundamental,” McGraw-Hill Book Company, USA, 1988.

H. Y. Nanlohy, “Perbandingan Variasi Derajat Pengapian Terhadap Efisiensi Termal Dan Konsumsi Bahan Bakar Otto Engine Be50,” Jurnal Dinamika Fakultas Teknik Universitas Halueleo, Kendari, Vol. 3 No. 2 Mei 2012.

W. W. Pulkrabek, “Engineering Fundamentals of the Internal Combustion Engine,” Prentice Hall, Upper Saddle River –

New Jersey 07458, 1997.

Y. R. Sadiq, “A Study on Influence of Ignition Timing on Performance and Emission of Petrol Engine,” Global Jurnal For Research analysis, vol. 5, Issue. 2, Feb- 2016. ISSN N0 2277-8160

A. Setiyawan, “Kajin Eksperimental Pengaruh Etanol Pada Premium Terhadap Karakteristik Pembakaran Kondisi Atmosferik Dan Bertekanan Di Motor Otto Silinder Tunggal Sistem Injeksi,” T.A., Fakultas Teknik Program Studi Teknik Mesin, Depok, 2012.

I. Siswanto dan Y. Efendi “Peningkatan Performa Sepeda Motor dengan Variasi CDI Programmable,” Jurnal Science Tech LP2M UST Yogyakarta, vol. 1, No. 1, 2015.

I. M. Suarta, “Pengaruh Kadar Air Pada Etanol Terhdap Kecepatan Pembakaran Dalam Hele Shaw Cell,” Jurnal Matrix Vol. 2, No. 1 Maret 2012

M. Syahril, B. S. Untoro, and S. Leydon, “Pengaruh Variasi Unjuk Derajat Pengapian Terhadap Kerja Mesin,” Jurnal Teknik Vol.3 No.1/APRIL2013. ISSN 2088-3676, 2013.

M. A. Wahid, “Pemanfaatan Bio-Etanol Sebagai Bahan Bakar Kendaraan Berbahan Bakar Premium,” Jurnal Prospek Pengembangan Bio-Fuel sebagai Substitusi Bahan Bakar Minyak, Vol.2, No.2, 2005.

I. G. Wiratmaja, “Analisa Unjuk Kerja Motor Bensin Akibat Pemakaian Biogasoline,” Jurnal Ilmiah Teknik Mesin, Vol. 4 No. 1, 2010.

F. Yuksel dan B. Yuksel, “The use of Ethanol-gasoline blend as a fuel in an SI engine,” Turkey: fakulty of engineering, Department of Mechanical Engineering, University of Ataturk. Vol. 29. Pp. 1181-1191, 2004.

DOI: https://doi.org/10.20961/mekanika.v17i2.35124

Refbacks

  • There are currently no refbacks.