The Utilizing Cutting Fluid And Feeding Rate Effect To The Surface Hardness And Precission Of Aluminum Material Using Cnc Milling Machine

Widhaya Bastian Purnama, Indri Yaningsih, Heru Sukanto

Abstract

There are many factor affecting the quality of product that are produced from milling machine process. The quality is mostly about surface roughness and precision. Those affecting factors are the selection of cutting parameter and use of cutting fluid. The research is done in order to know the effect of using cutting fluid and feed rate to aluminum on surface roughness and precision using Milling CNC machine. This research uses milling CNC Mitsubishi M70 machine. The free variables of feed rate are 20, 32, 45, 69, 108 mm/min. Each feed rate variations are given cutting fluid and no- cutting fluid treatment. The cutting fluid used is bromus oil which is mixed with water. The tests performed were surface roughness test, precision test. The result of this study shows that feed rate is in line with surface roughness. The use of cutting fluid affects surface roughness. The surface roughness score at feed rate variation using coolant treatment are 20, 32, 45, 69, 108 mm/min shows the surface roughness score of 0,442; 0,484; 0,553; 0,643; 0,797 μm. surface roughness score without cutting fluid treatment reveals the score of 0,470; 0,517; 0,582; 0;662; 0,847 μm. According to statistical analysis result using two way ANOVA, it can be concluded that the use of cutting fluid and feed rate affect precision at 95% trust rate. The measurement of A dimension using cutting fluid in the variation of feed rate 20, 32, 45, 69, 108 mm/min shows the precision rate of 99,999348; 99,99929; 99,999304; 99,999261; 99,9992 %. While, the variation without cutting fluid treatment reveals the precision rate at 99,999188 ; 99,999184; 99,999037; 99;998884; 99,998684 %.

Full Text:

PDF

References

M.T. Hayajneh, M. S. Tahat, and J., Bluhm, “Study of Effect of Machining Parameter on Surface Roughness in the End- Milling Proces,” Jordan J. of Mech. and Ind. Eng., vol.1 no.1 pp. 1-5, 2007.

O. Cakir, A. Yardimeden, T. Ozben, and E. Kilickap, “Selection of Cutting Fluids in Machining Processes,” J. of Achiev. in Mater. and Manuf. Eng., vol. 25 no. 2, 2007.

A. A. Rizkiani, A. A. Sonief, and Purnami. “Pengaruh Spindel Speed, Feed Rate, dan Kemiringan Pahat Pada Proses Pemakanan Conventional Miring Menggunakan Pahat End Mill Terhadap Kekasaran Permukaan,” Jurusan Teknik Mesin Fakultas Teknik Universitas Brawijaya, 2013.

T. Rochim, “Spesifikasi Geometris Metrlogi Industri dan Kontrol Kualitas, Laboratorium Teknik Produksi dan Metrologi Industri,” Jurusan Teknik Mesin, FTI, ITB. 2001.

B. Armunanto,“Teknik Pengukuran (Metrologi Industri),” ATMI PRESS, 2001.

A. A. Syah, E. Sutikno, and R. Raharjo, “Pengaruh Feed Rate dan Depth of Cuts Terhadap Surface Roughness Pada Proses Milling Dengan Bantuan 4 Axis CNC Machine,” Jurusan Teknik Mesin Fakultas Teknik Universitas Brawijaya, 2014.

S. Muktiwibowo, E. Sutikno, and T. Oerbandono, “Pengaruh Depth of Cut dan Variasi Cutting Fluid Terhadap Surface Roughness Aluminium 6061 Hasil Proses Turning,” Jurusan Teknik Mesin Fakultas Teknik Universitas Brawijaya, 2011.

D. Rahdiyanta, “Cairan Pendingin Untuk Proses Pemesinan,” Universitas Negeri Yogyakarta, 2010.

G. Boothroyd, “Fundamentals of Metal Machining and Machine Tools,” McGraw Hill Book Co, 1985.

S. Lubis and S. A. Yanuari, “Pengaruh Parameter Pemotongan Pada Proses Side Milling dan Face Milling Terhadap Kekasaran Permukaan Logam,” Jurusan Teknik Mesin Universitas Tarumanagara, 2014.

L. Kirkup and B. Frenkel, “An Introduction to Uncertainty in Measurement,” Cambridge University Press, 2006.

A. Daryus, “Proses Produksi,” Universitas Darma Persada, 2008.

A. N. P. Emad and K. K. P. Ali, “Computer-Based Design and Manufacturing,” Springer, 2007.

F. Klocke, “Manufacturing Processes 1 Cutting Translated by Aaron Kuchle,” Library of Congress Control, no. 2011925556, 2011.

R. A. Patil, V. D. Shinde, H. V. Shete, and S. P. Nevagi, “Effect of High Pressure Coolant on Surface Finish in Turning Operation,” Int. J. of Innov. Research in Sci., Eng. and Tech., ISSN 2319-8753, 2013.

SolidCAM “Milling Training Course 2.5D Milling,” SolidCAM, 2013.

SolidCAM “Milling User's Guide,” vol. 1, SolidCAM LTD, 2013

DOI: https://doi.org/10.20961/mekanika.v16i1.35049

Refbacks

  • There are currently no refbacks.