STRUKTUR MIKRO DAN KEKERASAN BAJA S45C PADA PENGELASAN SMAW DENGAN VARIASI MEDIA QUENCH

Nizam Effendi

Abstract


The purpose of this research is to find out the effect of current on microstructure and hardness value in S45C steel before (raw material) and after welding using Shielded Metal Arc Welding (SMAW). This research using experiment method. The Technique of data analysis using descriptive comparative research. The instruments that used for testing microstructure and hardness is Olympus Metallurgical Microscope and Vickers Hardness Tester. Based on the results of the research conclude that (1) the results of the microstructure testing showed the improved martensite structure after welding. In the raw material, martensite structure didn’t exist but the result of SMAW welding methods using quenching media of water, oil, and air that showed martensite structure was exist. (2) The hardness value of raw material is 232 VHN. The specimen with water media had highest average hardness value that is 411 VHN, oil media had average hardness value that is 308 VHN, air media had lowest average hardness value that is 263 VHN. This research showed that the result of SMAW welding using varying quenching media can changed the microstructure and hardness of S45C steel.


Keywords


hardness; microstructure; quenching; SMAW, S45C steel

Full Text:

PDF
rticle

References


Amanto, H. & Daryanto. 1999. Ilmu Bahan. Jakarta: Bumi Aksara.

ASM International. 1991. Heat Treating Volume 4. Untited State of America.

Erizal. 2011. Kajian Eksperimen Pengujian Kekerasan Baja Karbon Medium yang Disambung dengan SMAW dan Quenching dengan Air Laut. Jurnal Teknik Mesin. Universitas Prof. DR. Hazairin, SH Bengkulu.

Erizal. 2011. Analisa Struktur Mikro pada Daerah Las dan HAZ Hasil Pengelasan Shielded Metal Arc Welding (SMAW) pada Baja Karbon Medium Dan Quenching Air Laut. Jurnal Teknik Mesin Universitas Prof. DR. Hazairin, SH Bengkulu.

Putra, Y.P., Pintowantoro, S., & Sadino. 2008. Analisa Tegangan Sisa dan Distorsi pada Pengelasan Fillet T-Joint dengan Metode Elemen Hingga. Jurnal Teknik Material & Metalurgi. Institut Teknologi Surabaya.

Rananggono, D., Mulyadi, Y., & Winarno, GD. 2008. Studi Kekuatan Mekanik dan Struktur Mikro Hasil Pengelasan SMAW dengan Variasi Preheat dan Postheat Menggunakan Metode Pendinginan Cepat dan Pendinginan Lambat. Jurnal Tugas Akhir. Institut Teknologi Surabaya.

Santoso, Joko. 2006. Pengaruh Arus Pengelasan terhadap Kekuatan Tarik dan Ketangguhan Las SMAW dengan Elektroda E7018. Skripsi Universitas Negeri Semarang.

Setiawan, Ferry. 2016. Pengaruh Variasi Sudut Kampuh V dan Kuat Arus dengan Las Shielded Metal Arc Welding (SMAW) pada Baja A36 terhadap Sifat Mekanik. Jurnal Ilmiah Teknik Mesin. Universitas Muhammadiyah Sidoarjo.

Suharno. 2018. Teknologi Pengelasan Logam: Metalurgi dan Aplikasinya. Surakarta: UNS Press.

Suharno. 2008. Struktur Mikro Las Baja C-Mn Hasil Pengelasan Busur Terendam dengan Variasi Masukan Panas. Jurnal Teknik Mesin Universitas Kristen Petra Surabaya. Vol. 10, No. 1, April 2008: 45 –45.

Van Vlack. 1985. Elements of Materials Science and Engineering 5th Edition. USA: Addison Wesley Publising Company, Reading, Mass.

Wiryosumarto. 2000. Teknologi Pengelasan Logam. Jakarta: Pradnya Paramita.




DOI: https://doi.org/10.20961/jiptek.v12i1.28916

Refbacks

  • There are currently no refbacks.


Copyright (c) 2019 Nizam Effendi

View My Stats

Lisensi Creative Commons
This work is licensed under a Creative Commons Attribution 4.0 International License.