Optimizing the Composition of Basalt and Heat Treatment of Fly Ash-Based Mullite Ceramics Using the Taguchi Method

Tumpal Ojahan Rajagukguk, Anang Ansori, Ferdy - Ardiyansyah, Yusup Hendronursito

Abstract

The development of industrial activities has an impact on the increase in waste produced, and fly ash, aluminum dross, and basalt dust are no exception. This research studies the potential of these three materials as ceramic materials. Basalt dust from East Lampung was used as filler. The effect on the physical and mechanical properties of mullite (3Al2O3-2SiO2) ceramics was studied. The manufacture of mullite ceramics based on Taguchi design includes fly ash compositions of 40%, 50%, and 60% and basalt content of 0%, 5%, and 10%. sintering temperatures of 600°C, 900°C, and 1,200°C. Taguchi and Anova were used to determine the effect of independent variables on hardness and density. In addition, macro and microphoto tests were carried out to determine the physical and topographic changes of mullite ceramics. Chemical composition tests with X-ray fluorescence were carried out on raw materials and ceramics that have been formed. Changes in the crystal phase in mullite ceramics were studied through the X-ray diffragment test. XRF test results obtained for raw fly ash (SiO2 + Al2O3 + Fe2O3): 84.84 wt%. The composition of raw basalt is predominantly 48.42% SiO2, 18.82% Al2O3, 12.60% Fe2O3, and raw aluminum dross with 67.821% Al2O3 content. The mullite ceramic specimen consists of 38.24–45.30% SiO2, 34.72–48.73% Al2O3, 6.3–9.99% Fe2O3, and 2.31–5.31% CaO. The crystal phases formed are mullite, pyroxene, and diopside. Analysis of variance shows that hardness is significantly affected by sintering temperature, with a P-value of 0.013 and a contribution of 93.77%. This modeling is acceptable with an error value of 1.26%, or R-sq: 98.74%. The addition of basalt increases the density of mullite ceramics, with a P-value of 0.033 and a contribution of 96.05%. The addition of basalt as a filler is not able to increase the hardness significantly, but it affects the higher ceramic density value. However, the formation of mullite is interesting to study further as a refractory material

Keywords

Fly Ash; Aluminum Dross; Basalt; Ceramics; Mullite; Hardness

Full Text:

PDF

References

A. F. Widiyanto, S. Yuniarno, and K. Kuswanto, “Polusi Air Tanah,” J. Kesehat. Masy., vol. 10, no. 2, p. 246, 2015.

K. A. P. Saraswati and M. Razif, “Potensi Pemanfaatan Slag Aluminium Sebagai Substitusi Semen Dalam Proses Stabilisasi/Solidifikasi Limbah B3 Dengan Kajian …,” ENVIROTEK J. Ilm. Tek. …, vol. 12, no. 2, 2020, [Online]. Available: http://envirotek.upnjatim.ac.id/index.php/envirotek/article/view/69%0Ahttp://envirotek.upnjatim.ac.id/index.php/envirotek/article/download/69/67

S. Wardani, “Pemanfaatan Limbah Batu Bara ( Fly Ash ) Untuk Stabilitas Tanah Maupun Keperluan Teknik Sipil Lainnya Dalam Manggurangi Pencemaran Lingkungan,” Pengukuhan Guru Besar Fak. Tek. Univ. Diponogoro, pp. 1–71, 2008.

C. T. Foo, M. A. M. Salleh, K. K. Ying, and K. A. Matori, “Mineralogy and thermal expansion study of mullite-based ceramics synthesized from coal fly ash and aluminum dross industrial wastes,” Ceram. Int., vol. 45, no. 6, pp. 7488–7494, 2019, doi: 10.1016/j.ceramint.2019.01.041.

M. Romero, I. Padilla, M. Contreras, and A. López‐delgado, “Mullite‐based ceramics from mining waste: A review,” Minerals, vol. 11, no. 3, pp. 1–39, 2021, doi: 10.3390/min11030332.

Y. Hendronursito, J. Barus, M. Amin, M. Al-Muttaqii, T. O. Rajagukguk, K. Isnugroho, and D. C. Birawidha, ”The Local Mineral Potential From East Lampung-Indonesia : The Use Of Basalt Rock As A Stonr Meal For Cassava Plsnt ., vol. 5, no. 53, pp. 2502–2458, 2018, doi: 10.15243/jdmlm.

Y. Hendronursito, T. O. Rajagukguk, R. N. Safii, A. Sofii, K. Isnugroho, D. C. Birawidha, M. Amin, and M. Al-Muttaqii, “Analysis of Aluminium Basalt Particulate Composite Using Stirring Casting Method Through Taguchi Method Approach,” IOP Conf. Ser. Mater. Sci. Eng., vol. 807, no. 1, 2020, doi: 10.1088/1757-899X/807/1/012003.

S. Oktamuliani, Samsidar, M. Nasri, and Nehru, “Identifikasi Mineral Pada Batuan Granit Di Geopark Merangin Provinsi Jambi Menggunakan X-Ray Diffraction ( Xrd ) Dan,” JoP, vol. 1, no. November 2015, pp. 12–17, 2015.

H. Yildirim, M. Sümer, V. Akyüncü, and E. Gürbüz, “Comparison on efficiency factors of F and C types of fly ashes”, Construction and Building Materials, vol. 25, no. 6, pp. 2939-2947, 2011)

H. L. Yang, Z. S. Li, Y. D. Ding, Q. Q. Ge, Y. J. Shi, and L. Jiang, “Effect of Silicon Source (Fly Ash, Silica Dust, Gangue) on the Preparation of Porous Mullite Ceramics from Aluminum Dross,” Materials (Basel)., vol. 15, no. 20, 2022, doi: 10.3390/ma15207212.

F. Yang, C. Li, Y. Lin, and C. A. Wang, “Effects of sintering temperature on properties of porous mullite/corundum ceramics,” Mater. Lett., vol. 73, no. August 2021, pp. 36–39, 2012, doi: 10.1016/j.matlet.2011.12.087.

A. Prof, E. Abi, S. B. Gürel, İ. Özer, and P. E. Ö. F, “Production of Cordierite-Mullite Ceramic Composite From Olivine,” vol. 1, no. 12, pp. 3–5, 2013.

M. Chen, J. Liu, and Z. Wu, “Effect of Fe2O3 Concentration on the Properties of Basalt Glasses,” J. Nat. Fibers, vol. 00, no. 00, pp. 1–11, 2020, doi: 10.1080/15440478.2020.1758277.

H. Li, Y. Liu, Y. Liu, Q. Zeng, K. Hu, Z. Lu, and J. Liang, “Effect of sintering temperature in argon atmosphere on microstructure and properties of 3D printed alumina ceramic cores,” J. Adv. Ceram., vol. 9, no. 2, pp. 220–231, 2020, doi: 10.1007/s40145-020-0362-0.

W. Wang, K. Sun, and H. Liu, “Effects of different aluminum sources on morphologies and properties of ceramic floor tiles from red mud,” Constr. Build. Mater., vol. 241, p. 118119, 2020, doi: https://doi.org/10.1016/j.conbuildmat.2020.118119.

B. Jivov, M. Aleksandrova, S. Yordanov, and K. Toncheva, “Synthesis , phase composition and microstructure of colored ceramic materials based on diopside,” vol. 79, no. 3, pp. 77–79, 2020.

R. Titorenkova, V. Kostov-Kytin, and T. Dimitrov, “Synthesis, phase composition and characterization of Co-diopside ceramic pigments,” Ceram. Int., vol. 48, no. 24, pp. 36781–36788, 2022, doi: 10.1016/j.ceramint.2022.08.242.

S. Jin and H. Xu, “Study on structure variations of incommensurately modulated labradorite feldspars with different cooling histories,” Am. Mineral., vol. 102, no. 6, pp. 1328–1339, 2017, doi: 10.2138/am-2017-6003.

S. V. Vassilev, R. Menendez, M. Diaz-Somoano, and M. R. Martinez-Tarazona, “Phase-mineral and chemical composition of coal fly ashes as a basis for their multicomponent utilization. 2. Characterization of ceramic cenosphere and salt concentrates,” Fuel, vol. 83, no. 4–5, pp. 585–603, 2004, doi: 10.1016/j.fuel.2003.10.003.

S. V. Vassilev and R. Menendez, “Phase-mineral and chemical composition of coal fly ashes as a basis for their multicomponent utilization. 4. Characterization of heavy concentrates and improved fly ash residues,” Fuel, vol. 84, no. 7–8, pp. 973–991, 2005, doi: 10.1016/j.fuel.2004.11.021.

R.-M. Ion et al., “Archaeometric Investigations of the Chalcolithic Pottery from Topolița—Neamț County, Romania,” Coatings, vol. 13, no. 3, p. 488, 2023, doi: 10.3390/coatings13030488.

M. Pavlovic, M. Dojcinovic, R. Prokic-Cvetkovic, L. Andric, Z. Ceganjac, and L. Trumbulovic, “Cavitation wear of basalt-based glass ceramic,” Materials (Basel)., vol. 12, no. 9, 2019, doi: 10.3390/ma12091552.

G. Chen, H. Qi, W. Xing, and N. Xu, “Direct preparation of macroporous mullite supports for membranes by in situ reaction sintering,” J. Memb. Sci., vol. 318, no. 1–2, pp. 38–44, 2008, doi: 10.1016/j.memsci.2008.01.034.

L. F. Lima, P. Q. Mantas, A. M. Segadães, and R. C. D. Cruz, “Processing and characterization of sinter-crystallized basalt glass-ceramics,” J. Non. Cryst. Solids, vol. 538, no. December 2019, p. 120019, 2020, doi: 10.1016/j.jnoncrysol.2020.120019.

Refbacks

  • There are currently no refbacks.